Overview
HD cards have the ability to transmit and detect digits on all the TS of 10 ports of HD cards.
Above test was conducted with the response time of 200ms and latency 100ms on a Rack Mount PC having the configuration of
Pentium IV 2.8 GHz, 512 MB RAM & 40 GB Hard Disk.
The sample script is shown below:
set latency 100;
set response 200;
monitor dtmf digits #1,2,3,4,5,6,7,8,9,10:1..31;...
tx dtmf digits ("1 2 3 4 5 6 7 8 9 0 * # a b c d ",-10, 20,20) #1,2:1..31;
tx dtmf digits ("1 2 3 4 5 6 7 8 9 0 * # a b c d ",-10, 10,10) #3,4:1..31;
tx dtmf digits ("1 2 3 4 5 6 7 8 9 0 * # a b c d ",-10, 10,10) #5,6:1..31;
tx dtmf digits ("1 2 3 4 5 6 7 8 9 0 * # a b c d ",-10, 10,10) #7,8:1..31;
tx dtmf digits ("1 2 3 4 5 6 7 8 9 0 * # a b c d ",-10, 10,10) #9,10:1..31;
//end task *;
- Digit Detector configuration file option:
Digit detector configuration file option detects and reports DTMF/MF/MFC-R2 digits on channels as they occur. GL's HD cards
have the ability to transmit and detect digits on all the timeslots.
- Call capture using WCS
Simulation of MFC-R2 answer call using Windows Client Server script:
In this script the near end card initially transmits idle signal and waits for the other end to send line seize signal. After receiving
the line seize it will send line seize acknowledge signal to the other end, which is waiting for it. When near end receives MFCR2-F
digits, it transmits MFC-R2 backward digits. After finishing the transmission of backward digits, it will send an answer signal to the
far end. Call gets established. The near end card transmits a voice file from GL's card for a specified duration (10 sec). The call may
be terminated either at near end or at far end. In first script, near end will simply wait for idle signal from the other end and after
receiving the idle signal it will transmit the same to far end. Thus terminating the call. In second script, the near end will send a
clear back signal and wait for idle signal from the other end. Then it will transmit idle signal to complete the call termination.
Click here to view the near and far end termination of
MFC-R2 answer call script
Simulation of MFC-R2 place call using Windows Client Server:
In this script the near end card initially transmits idle signal and waits for the other end to send the same. After receiving the idle
signal from far end it transmits line seize signal to far end, and waits for line seize acknowledge signal. Near end now initiates the
dialing. After completion of dialing it will wait for answer signal from far end. The near end card transmits a voice file from GL's card
for a specified duration (10 sec). The call may be terminated either at near end or at far end. In first script near end will simply wait
for clear back signal from the other end and after receiving the same it transmits idle signal to far end, terminating the call. In second
script the near end will send idle signal and wait for the same from other end to terminate the call.
Click here to view the near and far end termination of
MFC-R2 place call script
Buyer's Guide:
Please Note: The XX in the Item No. refers to the hardware platform, listed at the bottom of the Buyer's Guide,
which the software will be running on. Therefore, XX can either be HDT, HDE, HUT, HUE, UTA or UEA depending upon
the hardware.
Back to Client/Server Scripted Control Software Page
